Chip Spreader

CSV Performance Features

Aggregate Delivery: Variable
Tier 4 Final - 275 hp (205 kw)
Weight: 23,720 lbs (10,759 kg)

Overall Length: 25’ 10” (7.874 m)
Overall Width: 8’ 6” (2.59 m)
Overall Height: 8’ 8” (2.64 m), beacon retracted
Wheelbase: 12’ 10.5” (3.92 m)
Turning radius: 26’ (7.92 m) outside turn radius
22’ 3” (6.78 m) inside turn radius

23,720 lbs (10,759 kg), unloaded
36,000 lbs (16,329 kg), loaded 16’ (4.87 m) wide

Shipping Information:
Length: 25’ 10” (7.87 m)
Width: 8’ 6” (2.59 m) with hopper
Height: 8’ 8” (2.64 m)

Fan Drive System:
45 cc/rev pump to provide optimal flow to the fan drive and steering circuit
1,325 psi orbital steering

Spread Hopper:
0’ to 16’ (0 to 4.87 m) hopper
Individual gate controls that are operated from the control station via electric over hydraulic
12” (.304 m) augers
Spread roll diameter of 6.625” (168.275 mm), 0.25” (6.35 mm) thick wall
Spread roll maximum speed approximately 150 rpms
Full length rejection screen on the spread hopper, maximum opening of 1” (25.4 mm)
Capacity: 1 cubic yards (.764 cubic m) per side

Rear Hopper:
Two independent manual flow control gates easily accessible from operator’s station for the conveyors
Skirting in the receiving hopper to minimize spillage
Capacity: 3.5 cubic yards (2.67 cubic m) struck
Receiving width: maximum 11’ 10” (3.6 m), minimum 9’ 6” (2.89 m)

Conveyor Belts:
Two independently operated, aggregate feed conveyors
Adjustable tail pulleys with pillow block style bearings, grease zerks for each bearing
Auto and manual system controlled from touch pad system integrated with Plus+1 system
Belt width: 20” (.508 m)
Speed: 0 to 550’ per minute (167.64 m per minute)

Truck Hitch:
Electric over hydraulically adjustable
Electronically controlled from the driver’s station
Electronic over hydraulic released locking mechanism
Spring loaded, hydraulically adjustable with hydraulic release

Control Functions:
Hydrostatic control system
Manual mode: Operator can vary forward/reverse speeds of unit with joystick
Speed ranges: 0 to 20 mph (0 to 32.1 kph), high range
0 to 10 mph (0 to 16 kph), low and reverse ranges
Application rate control:
- Computer monitors the actual speed of the spreader, varies gate opening to maintain the set application rate
- Plus+1 CAN Bus system with auto-rate control monitors actual speed of the spreader regardless of load conditions
- Programmable application rate in lbs per sq. yard
- Include rock size, type, chipping width, feet per minute and accumulative totals
- Ability to access memory settings service screens, system faults, engine faults, machine settings, calibration settings and display units in English or metric
- Control switches for the working lights, turn/hazard signals and beacon

Additional Standard Equipment:
Temperature monitored hydraulic oil cooler
Two wheel drive, front wheel drive
Backup alarm
LED turn signals, work lights and beacon
Remote camera for hitch
Pressure transducers

Optional Equipment:
All-wheel drive system
Dual operator consoles with slides
Spread hopper vibrators
Tool and storage box
Umbrella, quantity 2

Tier 4 Final, 275 hp (205 kw) Cummings diesel turbocharged engine
Proportional hydraulic fan drive: maximize hp (kw), reduce noise and automatic cleanout
Fuel filter, fuel water separator filter
12 volt negative ground system
Dual 1000 amp, 12 volt batteries
Dry type dual air cleaner system with indicator
Electrical variable controlled engine throttle
Fuel reservoir: 50 gallons (189 l)

Hydrostatic Pump Drive:
Single H1 electric controlled pump
10.07 cubic in (165,017 cubic mm) rev designed to provide optimum traction for two or four wheel drive system
Hydraulic pump has pressure compensating pump for auxiliary systems
Hydraulic reservoir: 75 gallons (283 l)

Auxiliary Pump System:
Capacity to operate the hydraulic gate cylinder, hopper extension , augers, conveyors and spread roll on aggregate hopper
Auxiliary circuits have minimum 500 psi relief setting for the hydraulic gate cylinder
2,500 psi conveyor

Front Axle:
52,900 lbs (23,995 kg) rated capacity, oscillating type
24.97:1 ratio, wet disc brakes, 5,400 lbs (2,449 kg) application
Powered by 9.82 cubic in (160,921 cubic mm), rev two-speed hydraulic drive motor
Automotive type, drive shaft axle connection between axle and hydraulic drive motor

Rear Axle:
Two-wheel drive system
Minimum 22,500 lbs (10,205 kg) rated capacity
16.5” (.419 m) diameter, 7” (177.8 mm) wide brakes, manual slack adjusters
Drum type brakes, spring applied and hydraulic released
Minimum 7” (177.8 mm) ground clearance

Track width front: 6’ 3” (1.9 m)
Track width rear: 6’ 9” (2.05 m)
Tires standard size: 385/65R 22.5
Wheels: budd-disc style

Operator’s Area:
One full console on left side, 15” (38.1 cm) slide out platform for optional field of view
Right hand remote operator control
Appropriate foot brake control
Parking brake electronically controlled on main control console
Access to engine and hydraulic components accessible from operator’s deck
Cushioned and adjustable seat

Fully hydraulic, orbital type
Independent of drive system

Two wheel drive: Front axle hydraulic multiple wet disc type
Rear axle hydraulic actuated brakes, spring applied and hydraulic released

Plus+1 CAN Bus control and onboard diagnostic system
DP 710 color graphic display, 7” (177.8 mm), 800 x 480 pixel
Gauges include engine water temperature, engine oil pressure, tachometer, fuel gauge, DEF fluid, voltmeter, hydraulic temperature, hour meter and volt meter

Training, Support and Company:
Training and support manuals
Optional on-site operator training by Dealer
One-year, unlimited hours warranty against any manufacturer defects
Extended warranty available
50+ years manufacturing experience
ISO 9001 Certified
Manufactured in the USA